Free Guide to Using a Car Jack Safely

Understanding Car Jack Types and Their Proper Uses

A car jack is a mechanical device designed to lift a vehicle off the ground for maintenance, repairs, or tire changes. Before you use any jack, you need to understand which type you have and what it's meant to do. The three most common types are scissor jacks, hydraulic jacks, and bottle jacks.

Get Your Free Elkton Maryland Unemployment Office Locations Guide →

Scissor jacks use a screw mechanism that extends or retracts to raise and lower a vehicle. These come standard in many cars and are compact, making them easy to store in your trunk. They work by turning a handle that tightens the screw, which pushes the X-shaped frame upward. Scissor jacks typically have a maximum lifting capacity between 1 and 2 tons, though some heavier-duty models reach 3 tons. They are best used for changing tires in roadside situations because they lift vehicles slowly and require more physical effort than other types.

Hydraulic jacks use fluid pressure to lift vehicles and are commonly found in repair shops and garages. These jacks can lift heavier loads more quickly than scissor jacks—many models support 2 to 4 tons or more. A hydraulic jack operates when you pump a handle, which forces hydraulic fluid through a valve system, creating upward pressure. These are more expensive than scissor jacks and require more space, but they are faster and easier to operate for repeated use.

Bottle jacks are cylindrical hydraulic jacks that look like a bottle standing upright. They offer a middle ground between scissor and floor jacks, with lifting capacities of 2 to 20 tons depending on the model. Bottle jacks are compact, portable, and powerful, making them popular for both home garages and emergency roadside kits.

Practical takeaway: Check your vehicle's owner manual to identify which jack came with your car and learn its specific weight capacity. Write down this information and keep it with your jack for reference.

Essential Safety Checks Before Using Your Jack

Before you lift your vehicle with any type of jack, you must perform several safety checks to prevent accidents and equipment failure. These preliminary steps take only a few minutes but significantly reduce the risk of injury or vehicle damage.

Get Your Free Polyester Fabric Care Guide →

First, inspect your jack for visible damage. Look for cracks, dents, bent metal, or leaking hydraulic fluid. If a jack has been in a car accident, check it carefully—metal fatigue from impact can cause sudden failure during use. Hydraulic jacks should have no oil leaks around the base or lifting arm. If you find leaks, the jack is unsafe and should be repaired or replaced before use. Scissor jacks should have all moving parts intact and operating smoothly when you manually turn the handle.

Check that the contact surface on top of the jack is clean and not stripped or damaged. This is the part that touches your vehicle, and any debris or damage here can cause the jack to slip or damage your car's frame. Wipe the contact surface with a clean cloth if needed.

For hydraulic and bottle jacks, check the fluid level according to the manufacturer's instructions. Most jacks have a fill plug or viewing window. If fluid is low, the jack may not lift properly or may lower suddenly under load. Never use an underfilled hydraulic jack.

Test your jack on level ground before using it under your vehicle. Operate it through its full range—raise it to maximum height and lower it back down. Listen for any unusual sounds like grinding or creaking. Feel for smoothness in the operation. If anything seems wrong, investigate before using the jack on your vehicle.

Practical takeaway: Create a simple checklist on your phone or keep a paper copy in your car with these inspection points: visible damage, fluid leaks (for hydraulic jacks), clean contact surface, proper fluid level, and smooth operation through full range.

Choosing the Right Location and Proper Vehicle Positioning

Where and how you position your vehicle before jacking it up is critical to safety. The wrong location can cause your vehicle to slip or tip, which can result in serious injury or death. According to the National Highway Traffic Safety Administration, improper jack placement contributes to many preventable vehicle incidents each year.

Update Your Apple Payment Method Information Guide →

Always work on level, solid ground. Never jack a vehicle on grass, gravel, or soft soil—the ground cannot support the weight and the jack will sink or tilt. Asphalt and concrete are ideal. If you must work on softer ground, place a wide, solid board under the jack base to distribute the weight. This board should be at least 12 inches square and made of wood or metal at least 1 inch thick.

Identify the proper jacking points on your vehicle. These are reinforced areas of the frame designed to support the jack. Most cars have four jacking points—two near the front wheels and two near the rear wheels. Consult your owner's manual to find the exact locations, as they vary by make and model. Never place a jack under plastic body panels, the oil pan, or areas without reinforcement. These will collapse under the vehicle's weight.

Turn off the engine and engage the parking brake firmly. If you're working on a manual transmission vehicle, leave it in gear. For automatic transmissions, leave it in Park. This prevents the vehicle from rolling or shifting during your work.

If possible, have someone sit in the driver's seat to keep weight in the vehicle and improve stability. At minimum, make sure no one stands directly under the vehicle or in the immediate area where it might roll if something goes wrong.

Practical takeaway: Before jacking any vehicle, take a photo of the jacking points from your owner's manual and save it on your phone so you can reference it anywhere.

Step-by-Step Instructions for Raising Your Vehicle Safely

Once you've confirmed your equipment is safe and chosen the right location, you can proceed with lifting. This process requires attention and deliberate movement to prevent accidents.

Learn About Driving With an Expired License →

Position the jack directly under the jacking point, making sure the contact surface is perpendicular to the ground. The jack should not be at an angle. For scissor jacks, make sure the handle socket is properly seated in the lifting mechanism before you begin. For hydraulic jacks, ensure the release valve (usually a screw at the bottom of the jack) is closed by turning it clockwise until snug—do not over-tighten.

Begin raising the vehicle slowly. Stop every few inches and visually confirm that the jack remains aligned with the jacking point and that the vehicle is lifting evenly. Listen for any popping sounds or sudden shifts. If something sounds or feels wrong, lower the vehicle immediately by reversing the process, and investigate the problem.

Raise the vehicle only as high as you need for your task. Many people lift too high, which increases instability. Generally, you need only 6 to 12 inches of clearance to remove a tire or perform basic maintenance.

Once the vehicle reaches the desired height, immediately secure it with jack stands rated for at least the vehicle's weight. Jack stands are the most important safety device you can use—a jack is meant for lifting, not for supporting a vehicle while you work under it. Place the stands directly under the vehicle frame or suspension components near where you're working. Lower the vehicle slightly onto the stands so it bears weight on both the jack and the stands.

Never rely on a jack alone to hold your vehicle up while you work. Jacks fail. Jack stands prevent catastrophic injury if a jack fails. According to the Consumer Product Safety Commission, many serious injuries each year result from vehicles falling when only a jack supports them.

Practical takeaway: Purchase jack stands rated for at least 150% of your vehicle's weight. If your vehicle weighs 4,000 pounds, buy stands rated for at least 6,000 pounds. Always use a pair of stands together.

Safe Operation and Lowering Procedures

How you operate the jack during your task and how you lower the vehicle are equally important as raising it. Improper technique during these stages causes many accidents.

Free Guide to Visiting Mount St. Helens →

While working, periodically check that the vehicle hasn't shifted on the jack or stands. Every 10 to 15 minutes, visually inspect the jacking points and jack position. If you notice any movement, immediately stop work and re-stabilize the vehicle.

Never crawl completely under the vehicle with only a jack supporting it. This is the most dangerous scenario. If the jack fails while you're underneath